The Foundation of Plumbing Knowledge for Bathtub Installation
The Foundation of Plumbing Knowledge for Bathtub Installation
Blog Article
Here in the next paragraph you might get more first-rate information and facts related to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Mounting a tub isn't exactly brain surgery, however it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old tub with a new one is likewise a reasonably challenging job. If the old tub is easily available, the job can relocate rapidly; if you need to open up a wall surface to get rid of the old tub and also position the new tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will need an assistant to vacate the old bathtub as well as set in the new one. Make certain you have qualified on your own for the task as well as are comfortable attempting it. As opposed to employing a specialist to take over a halfway-completed task, it is far better to consider utilizing one prior to you start. Possibilities are you may need a specialist plumber to make tube connections.
This article will assist you install a new tub in your shower room if you have already acquired a new tub as well as do not require to change the plan of your previous water pipes.
Your tools as well as material checklist must make up the following:
Planning for the Setup
Firstly, the sustaining framework supplied with the bath needs to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to ensure that if the faucet features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to prevent strain on the tub.
Fit the adaptable faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath must now be ready to be suited its last position.
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, then the first thing you must do is separate the water system. After doing so, activate the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing taps can be quite troublesome because of the limited access that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. As soon as the supply pipelines have actually been eliminated, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from turning throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing substance.
Prior to carrying on to fit the new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Using the two wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are handy in evenly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four little points.
The next goal is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and also readjusting the feet on the bath tub till the level checks out level.
To install taps, fit the bottom of the outermost flexible tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the other tap.
Turn on the water system as well as check all joints and new pipework for leakages as well as tighten them if required. Fill the tub and additionally inspect the overflow outlet and also the typical electrical outlet for leakages.
Finally, fix the bath paneling as described in the manufacturer's user's manual. Tiling and securing around the bathtub ought to wait till the tub has actually been utilized at least when as this will certainly settle it into its final setting.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the tap and also the other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin ensuring that the washing machines remain in area between the faucet and also the sink. Protect the tap in position with the producer supplied backnut. As soon as the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former type should be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to break a stiff seal, creating the water to penetrate the wall surface in between the bathroom and also the tiling, leading to complications with dampness as well as possible leaks to the ceiling below.
You can choose from a range of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes and cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly load the tub with water before securing, to enable the activity experienced when the tub remains in use. The sealer can crack fairly very early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally easily available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that article about A Step-by-Step Guide to Installing a Bathtub while doing a lookup on the web. Enjoyed reading our write-up? Please share it. Help someone else find it. I am grateful for your time. Kindly come visit our website back soon.
Ensure leak-free homes. Report this page